The scratch pattern will be wider with a coarser paper so therefore the color will be darker. Start with 120 grit before moving up to 180 and finally 220.
Getting A Proper Stain On Maple Plywood Finishing Wood Talk Online
December 25 2008 0333 PM.
Staining maple plywood. Tip Number 2 Always start staining on the backs so if you hate the stain experiment you will not see it every day. Chalky Posted in Finishing on January 10 2008 0401am I am in the process of making a sewing machine cabinet for my wife out of maple and birch plywood. Sand your plywood with 180 grit sandpaper and only 180 grit.
Heres advice on techniques that work. You can also control the way the wood accepts the stain by adjusting your sanding process. Staining maple to a dark hue which is very dense and quite light in color with an oil based or gel-style product is hard work.
Spraying stain is mostly an alternative to ragging or brushing prior to wipe down. As I recommended above you are gong to want to dilute to about 12-1lb cut. Ive ebonized solid maple many times before with great luck.
Problem is these non-porous woods dont give much place for the particles to lodge. You can get dewaxed shellac by the gallon under the name Bullseye Sealcoat. Maple is a very nice wood to stain Ive stained plywood too and the water-based stains turned out nicely.
First starting a lower grit such as 150 sand evenly across the side youll be staining. You wont want to add stain to a plywood surface that hasnt been sanded. Reply 5 on.
It barely soaked into the oak at all but looked much darker on the maple. Sanding the wood to 600 grit exacerbated the problem by burnishing the surface of the wood. Pine and birch were both splotchy and inconsistent.
You can spray without wiping dyes or top coats tinted with dye. Try to evenly sand the entire project with this final sanding. Pigment stain is made up of particles of color.
Rendering it even less able to absorb the stain than if you had stopped sanding at 180 or 220 grit. Question For a favorite client Im doing a small piece that needs to be stained dark black but not have a painted look. The stain did not take well on wood milled with the grain and on cross cuts the stain soaked into the wood giving a dark black color.
Then using some 320 grit paper sand exposed end grain which tends to stain. Can be sprayed brushed or applied with a flat pad style applicator. Once the floor is coated lightly sand with 180-220 grit paper.
The reason is that they are quite non-porous meaning they dont have many or large pores. I usually do this in a very approximate way by diluting the Sealcoat 50 with denatured alcohol. The key to evening out the stain is to sand the project thoroughly using progressively finer sandpaper grits.
How to accent maple with walnut stain. I have never used either before and the maple looks like it could be blotchy when stained. In other words if the plywood is coming out too light sand it with a coarser grit paper.
Stain for maple plywood. Any suggestions on staining. No matter what type of wood you have sanding is a very important step to do before staining.
Hopefully you can report back on what you found cause it would be very nice information to have - Good luck with your project. When sanding traditional wood boards its best to start with a lower grit and work up but if you try that with plywood youre likely to sand through the top layer. Log in or register to post comments.
Staining maple and birch plywood. Any suggestions would be appreciated. If you want a darker finish on Maple use a Dye.
In your case with maple ply wiping stain would be a challenge no matter how you first apply it due to the blotchy and uneven way maple talks a stain. I have also applied the finish before assembling the. Midnight-Black Stain for Maple Plywood Dead black is a tall order if you want a stain not a paint.
When staining soft maple Kitchen doors and drawers from a millworks shop the painter applied a special walnut stain directly to the raw wood. Tip Number 1 Do not stain. Instead carefully sand with 180 grit sandpaper.
When staining soft maple Kitchen doors and drawers from a millworks shop the painter applied a special walnut stain directly to the raw wood. Varathane Weathered Gray Stain The color of the Varathane Weathered Gray stain varied widely depending on the wood species. Then finish with a higher grit such as 220.
Maple Cherry and other woods of similiar makeup are known to be difficult to stain. I agree with Jim I have used Flecto Diamond water based floor finish with excellent results. Oak walnut cherry maple butcher block tops are on sale here.
And in my opinion not a good idea. Glue sizing definitely works but I generally prefer a wash coat of dewaxed shellac to help avoid blotching when stain is later applied I use Zinnsers SealCoat and dilute it 11 with denatured alcohol.
Stain Issues In Maple Plywood Coffee Table Woodworking Talk
Wood Veneer Skis
Staining Birch Plywood Quick Tip Youtube
Columbia Forest Products 3 4 In X 4 Ft X 8 Ft Purebond Maple Plywood 263012 The Home Depot
How To Overcome Staining Problems On Hard Maple
Cherry Stain Solid Maple Baltic Birch Plywood Rocket Mission
How To Stain Wood Evenly Without Getting Blotches And Dark Spots Diy Family Handyman
Varathane 8 Oz Colonial Maple Classic Wood Interior Stain 4 Pack 339731 The Home Depot
Help Needed Gel Stain On Maple Plywood Is Coming Out Blotchy Will This Be Fixed After A Few Finishing Clear Coats Woodworking
Stained Maple Plywood Page 1 Line 17qq Com
Maple Veneer Plywood Sanded 100 Then 159 Per General Finishes Label Applied One Coat Of General Finishes Oil Based Stain Pecan And Blotches Resulted Only Applied 1 Of 3 Coats Of Minwax
How To Overcome Staining Problems On Hard Maple
Maple Plywood Stained Google Search Staining Wood Maple Plywood Maple Wood
Comments
Post a Comment